Catalogue
FNIRSI Code: 401131

FNIRSI 1014D 2-in-1 oscilloscope signal generator

Not available
Description

FNIRSI 1014D 2-in-1 oscilloscope signal generator


The FNIRSI 1014D is a compact digital oscilloscope designed for electronic service, research and development departments, technical education and hobbyists. It allows simultaneous analysis and signal generation, which significantly increases the range of applications when diagnosing circuits, testing prototypes or learning to work with waveforms. The device has two input channels with 1 MΩ impedance and supports a bandwidth of 100 MHz at 1GSa/s sampling. A 7-inch LCD screen with a resolution of 800×480 px facilitates operation. Auto-analysis, FFT, X-Y mode and cursor recording are possible. There is also a 1GB internal memory with the ability to store up to 1,000 waveforms and 1,000 screenshots, and data can be easily exported to a computer via USB.




Fast signal analysis


A high sampling rate of 1GSa/s and a bandwidth of 100 MHz enable detailed analysis of analog and digital signals. This allows the device to catch even short-term anomalies in the waveform. Trigger modes include Auto, Single, and Normal, allowing the device to capture both interference pulses and regular analog signals, such as sinusoids.




Built-in DDS generator


The integrated DDS signal generator supports 14 standard waveforms (including sine, rectangle, sawtooth, triangle), with precise frequency adjustment in 1 Hz increments. The solution used allows generating signals with accurate parameters for testing and simulation. The output frequency range reaches up to 10 MHz (for sine wave), which allows testing a wide range of electronic and signal circuits.




Waveform capture function


The "capture output" function allows you to save part or all of the actual waveform from the oscilloscope as the generator's output signal. The ability to store up to 1,000 custom signals increases flexibility in testing and analysis. This solution distinguishes the FNIRSI 1014D from classic arbitrary generators, which rely solely on manual signal adjustment.




Overvoltage protection


An integrated high-voltage protection module allows the device to safely measure signals up to 400V (with x10 probe), reducing the risk of damage to the device during measurements in mains-powered systems. The protection function works automatically, so accidental use of the probe without switching to x10 does not risk damaging the equipment.




High readability display


The 7" TFT color screen with 800x480 pixel resolution provides a clear representation of waveforms. Auto mode and an intuitive interface allow you to quickly get an image of the signal without manual adjustment. Thanks to an intelligent detection algorithm, the device automatically adjusts the trigger level even for waveforms with multiple slopes or the so-called dead zone. Such a solution saves time and avoids interpretation errors. The oscilloscope can store up to 1,000 screenshots and 1,000 waveforms in its 1GB internal memory. The data can be viewed as thumbnails, which facilitates quick viewing and selection. The interface allows users to zoom in, delete and export records without exiting review mode.




Signal analysis functions


The built-in FFT function and X-Y waveform display mode allow you to analyze harmonics and compare the amplitudes and phase shifts of two signals. These are useful tools in the diagnosis of electronic circuits. In addition, the manual cursor measurement mode makes it possible to read the peak value and frequency without the need to recalculate the scale, which increases the precision of analysis even in distorted waveforms. The device uses a special algorithm for decoding the dial signal, eliminating the problem of erroneous readings caused by oxidation or wear of the mechanism. Even when the encoder is damaged, the oscilloscope works correctly.





Included:


  • FNIRSI 1014D 2-in-1 oscilloscope
  • 100 MHz probe x2
  • USB charger
  • User's manual


 





ManufacturerFNIRSIModel1014DChannels2LCD screen size7 inchesLCD screen resolution800 × 480Display technologyLCDFrequency response100 MHzSampling frequency1 GSa/sHighest test voltage1X: 40V, 10X: 400VCursorXY position
Y triggerRolling mode (roll)SupportedAutomatic calibrationSupportedWaveform recording1000 images + 1000 waveformsWaveform managementSupportedVoltage accuracy±5%Rise time< 3 nsMemory depth240 KbitInput resistance1 MΩSensitivity50 mV ~ 500 VTime base50 s ~ 10 nsTrigger modeSingle / Normal / AutoTrigger edgeAscending / DescendingCouplingAC / DCFrequency accuracy±0,01%Parameters12 typesGenerator14 typesCapture outputSupportedExtensionUSB exportPower supply5V 2A / 3A / 4ADimensions310 × 145 × 70 mm
Customer reviews

No reviews yet — reviews can be written from your order after purchase

Delivery and warranty

Delivery
Parcel locker
Courier
Pickup in store
Warranty
Manufacturer warranty
Official distributor
Invoice and warranty coupon included
Return
14-day right of withdrawal
Money-back guarantee
Free return for defective goods

Similar products

View all
Multifunctional signal generator FNIRSI SG-002
In supplier warehouse: >5
20.39 € / pcs.
FNIRSI SG-003A mini signal generator
In supplier warehouse: >5
66.89 € / pcs.
FNIRSI 2C53T 3-in-1 portable oscilloscope multimeter signal generator
In supplier warehouse: >5
84.60 € / pcs.
Fnirsi P6100 oscilloscope probe
In supplier warehouse: >5
7.81 € / pcs.
Portable 3-in-1 mini oscilloscope FNIRSI DSO-TC4
In supplier warehouse: >5
62.59 € / pcs.
Portable 2-in-1 mini oscilloscope FNIRSI DSO153 signal generator
In supplier warehouse: >5
36.57 € / pcs.
Portable 2-in-1 mini oscilloscope FNIRSI DSO510 signal generator
In supplier warehouse: >5
41.19 € / pcs.
FNIRSI LCR-P1 multifunctional capacitor and transistor tester
In supplier warehouse: >5
24.30 € / pcs.
Cart